Fuji Electric Base Board Micrex-SX SPH
Base Board Micrex-SX SPH type
- NP1BS-03
- NP1BS-06
- NP1BS-08
- NP1BS-11
- NP1BS-13
- NP1BP-13
- NP1BS-08S
- NP1BS-11S
- NP1BS-13S
- NP1BP-13S
- NP1BS-08D
- NP1BS-11D
- NP1BS-13D
- NP1BP-13D
Fuji Electric CPU Module PLC Micrex-SX SPH Series
Features
Ultra high-speed processing
The CPU module carries out the ultra high-speed processing in basic instructions as follows: SPH300 in 20ns, SPH200 in 70ns, SPH2000 in 30ns, and SPH3000 in 9ns.
Muiti-CPU configuration (SPH300/SPH2000/SPH3000)
Up to 8 CPUs can be configured while realizing the high-speed control by load distribution.
Redundancy (SPH300/SPH2000)
The 1 to 1 hot standby and the N to 1 cold standby improve the system safety and reliability. (The N to 1 cold standby is provided only to SPH300.)
IEC 61131-3
The series is fully compliant with the international standard language IEC 61131-3, which enables you to prepare the programming valid worldwide.
Compatible with USB and user ROM
The SPH300, SPH2000 and SPH3000 are provided as the USB and the user ROM versions in the separate format. (NP1PS-32R/74R/117R/245R, NP1PM-48R/48E/256E/256H and NP1PU-048E/256E)
Large-capacity battery (optional)
It is possible to extend the memory backup time to three and a half years (at 25°C) by adding an optional large-capacity battery to the SPH300 (74K/117K/245K steps).
SPH200
- NP1PH-08
- NP1PH-16
- NP1PS-74D
- NP1PS-32
- NP1PS-32R
- NP1PS-74R
- NP1PS-117R
- NP1PS-245R
- NP1PM-48R
- NP1PM-48E
- NP1PM-256E
- NP1PM-256H
- NP1PU1-256NE
- NP1PU2-048E
- NP1PU2-256E
- NP1PU-048E
- NP1PU-128E
- NP1PU-256E
Fuji Electric FRENIC AQUA Series Inverter
Inverter Fuji Electric for Pumps and Blowers
High performance enable by the comprehensive use of Fuji technology. Easy maintenance for the end-user. Maintains safety and protects the environment. Opens up possibilities for the new generation.
Fuji Electric Frenic Eco 3-phase 200V 0.75kW – 110kW
Inverter Fuji Electric Frenic Eco 0.75kW - 110kW 3-phase 200V models
- FRN0.75F1S-2A : 0.75kW
- FRN1.5F1S-2A : 1.5kW
- FRN2.2F1S-2A : 2.2kW
- FRN3.7F1S-2A : 3.7kW
- FRN5.5F1S-2A : 5.5kW
- FRN7.5F1S-2A : 7.5kW
- FRN11F1S-2A : 11kW
- FRN15F1S-2A : 15kW
- FRN18.5F1S-2A : 18.5kW
- FRN22F1S-2A : 22kW
- FRN30F1S-2A : 30kW
- FRN37F1S-2A : 37kW
- FRN45F1S-2A : 45kW
- FRN55F1S-2A : 55kW
- FRN75F1S-2A : 75kW
- FRN90F1S-2A : 90kW
- FRN110F1S-2A : 110kW
Fuji Electric Frenic Lift 3-phase 200V
Frenic Lift 3-phase 200V models
- FRN5.5LM1S-2EA : 5.5kW
- FRN7.5LM1S-2EA : 7.5kW
- FRN11LM1S-2EA : 11kW
- FRN15LM1S-2EA : 15kW
- FRN18.5LM1S-2EA : 18.5kW
Fuji Electric Frenic Lift 3-phase 400V
Optimum Exclusive Design for Passenger Elevators
- A braking circuit is built in the inverters of all the capacities
- Built-in PG feedback circuit is standard equipment.
- An optional keypad is available
Fuji Electric FRENIC Lift Series Inverter
Fuji Electric FRENIC Lift Series of exclusive AC Drives for operation of elevators are specially designed to have a number of improved features over previous elevator AC Drives, such as vastly lower torque ripple.
We have incorporated the functions that customers find most necessary in elevator controls to provide an AC Drive that delivers performance that fits your elevator system.
Fuji Electric Frenic Mini 1-phase 200V 0.1kW – 2.2kW
Features
- High starting torque, at 150% or more
- Trip-free operation
- Stable operation even for a step load
- Braking resistor connectable to the inverter
- Reduce motor instability at low speed
- The highly used functions for and pumps
- Automatic energy-saving provides as a standard functions
- PID control function
- Cooling fan On/Off control function
- Ideal functions to serve a multiplicity of need for small-capacity inverters
- Compatible with a wide range of frequency setting
- The output frequency can be set to a maximum of 400Hz
- A transistor output is provided
- Two point can be set for a non-linear V/f pattern
- Compact
- Simple operation and wiring
- Interface for peripheral devices and comprehensive protective functions
- Flexible through optionals
Fuji Electric Frenic Mini 3-phase 400V 0.4kW – 3.7kW
Inverter Fuji Electric Frenic-mini 0.4kW - 3.7kW 3-phase 400V Models
- FRN0.4C1S-4A : 0.4kW (1/2HP)
- FRN0.75C1S-4A : 0.75kW (1HP)
- FRN1.5C1S-4A : 1.5kW (2HP)
- FRN2.2C1S-4A : 2.2kW (3HP)
- FRN3.7C1S-4A : 3.7kW (5HP)
- FRN0.4C1E-4A : 0.4kW (1/2HP)
- FRN0.75C1E-4A : 0.75kW (1HP)
- FRN1.5C1E-4A : 1.5kW (2HP)
- FRN2.2C1E-4A : 2.2kW (3HP)
- FRN3.7C1E-4A : 3.7kW (5HP)
- FRN1.5C1S-4A21 : 1.5kW (2HP)
- FRN2.2C1S-4A21 : 2.2kW (3HP)
- FRN3.7C1S-4A21 : 3.7kW (5HP)
- FRN0.4C1J-4A : 0.4kW (1/2HP)
- FRN0.75C1J-4A : 0.75kW (1HP)
- FRN1.5C1J-4A : 1.5kW (2HP)
- FRN2.2C1J-4A : 2.2kW (3HP)
- FRN3.7C1J-4A : 3.7kW (5HP)
Fuji Electric Frenic Mini C1 3-phase 400V Series
Frenic Mini C1 3-phase 400V Series
Standard type
FRN0.4C1S-4A : 0.4kW
FRN0.75C1S-4A : 0.75kW
FRN1.5C1S-4A : 1.5kW
FRN2.2C1S-4A : 2.2kW
FRN3.7C1S-4A : 3.7kW
Semi-standard type
EMC filter built-in type
FRN0.4C1E-4A : 0.4kW
FRN0.75C1E-4A : 0.75kW
FRN1.5C1E-4A : 1.5kW
FRN2.2C1E-4A : 2.2kW
FRN3.7C1E-4A : 3.7kW
Braking resistor built-in type
FRN1.5C1S-4A21 : 1.5kW
FRN2.2C1S-4A21 : 2.2kW
FRN3.7C1S-4A21 : 3.7kW
IP40 enclosure type
FRN0.4C1J-4A : 0.4kW
FRN0.75C1J-4A : 0.75kW
FRN1.5C1J-4A : 1.5kW
FRN2.2C1J-4A : 2.2kW
FRN3.7C1J-4A : 3.7kW
Fuji Electric Frenic-eHVAC AC Drives
Features
Pursuit of cost competitiveness
Competitiveness realized with optimum design
Dedicated functionality for HVAC markets
Fire mode (fan control), built-in PID/Cascade operation (pump control), etc.
Built-in EMC filter as standard
Built-in category C2/C3 EMC filter as standard, catering for a variety of environments.
PM motor drive possible
PM motor drive is now possible with PM sensorless vector control
Enhanced customized logic
Equipped with customized logic as standard to facilitate the free programming of up to 200 steps
Unique functions tailored to the application or usage method can constructed
Comprehensive communication support
Equipped with BACnet communication protocol as standard to facilitate the productization of a variety of control and communication options.
Construction of system support is made easy with these functions.
- Standard support : RS485, Modbus RTU, BACnet MS/TP
- Option support : Profibus DP, DeviceNet, Lonworks, CC-Link
Multi-function keypad (option)
A Multi-function keypad with support for 19 languages is available as an option to realize worlwide deployment.
Fuji Electric FRN2.2LM1S-7EA Frenic Lift 1-phase 200V
Optimum Exclusive Design for Passenger Elevators
- A braking circuit is built in the inverters of all the capacities
- Built-in PG feedback circuit is standard equipment.
- An optional keypad is available
- Overload capacity : 200% for 10s
- Current response : 5 times greater than previous models (corporated with the G11UD series
- Reduction of torque ripple realizes low vibration
- Reduced roll-back during starting up
- Current response (ACR) : 500Hz
- Speed control accuracy : ±0.01%
- 200% of rated current for 10s (overload begins from 80% continous operation with a carrier frequency of 10kHz).
Fuji Electric Inverter Electric FRENIC-VG Series
FRENIC-VG Series
- High performance enabled by the comprehensive use of Fuji technology.
- Easy maintenance for the end-user.
- Maintains safety and protects the environment.
- Opens up possibilities for the new generation.
Fuji Electric Inverter Frenic Mega 5.5kW to 55kW 400V 3-phase
LD (Low Duty) Spec for ligh load
Wide Model Variation
Basic Type
Suitable for the equipment that uses a peripheral device to suppress noise or harmonics
EMC filter built-in type
By adopting built-in filter, this type is compliant with European EMC Directives category C3 (2nd Env) 'EN61800-3-2004'.
Frenic Mega 75kW to 630kW 400V 3-phase
- FRN5.5G1E-4A (7.5kW 400V 3 phase)
- FRN7.5G1E-4A (11kW 400V 3 phase)
- FRN11G1E-4A (15kW 400V 3 phase)
- FRN15G1E-4A (18.5kW 400V 3 phase)
- FRN18.5G1E-4A (22kW 400V 3 phase)
- FRN22G1E-4A (30kW 400V 3 phase)
- FRN30G1E-4A (37kW 400V 3 phase)
- FRN37G1E-4A (45kW 400V 3 phase)
- FRN45G1E-4A (55kW 400V 3 phase)
- FRN55G1E-4A (75kW 400V 3 phase)
Fuji Electric Inverter Frenic Mega 75kW to 630kW 400V 3-phase
Frenic Mega 75kW to 630kW 400V 3-phase
- FRN75G1E-4A (75kW 400V 3 phase)
- FRN90G1E-4A (90kW 400V 3 phase)
- FRN110G1E-4A (110kW 400V 3 phase)
- FRN132G1E-4A (132kW 400V 3 phase)
- FRN160G1E-4A (160kW 400V 3 phase)
- FRN200G1E-4A (200kW 400V 3 phase)
- FRN220G1E-4A (220kW 400V 3 phase)
- FRN280G1E-4A (280kW 400V 3 phase)
- FRN315G1E-4A (315kW 400V 3 phase)
- FRN355G1E-4A (355kW 400V 3 phase)
- FRN400G1E-4A (400kW 400V 3 phase)
- FRN500G1E-4A (500kW 400V 3 phase)
- FRN630G1E-4A (630kW 400V 3 phase)
Fuji Electric Inverter Frenic Mega 90kW to 400kW 400V 3-phase
Frenic Mega 90kW to 400kW 400V 3-phase
- FRN90G1E-4E (110kW 400V 3 phase)
- FRN110G1E-4E (132kW 400V 3 phase)
- FRN132G1E-4E (160kW 400V 3 phase)
- FRN160G1E-4E (200kW 400V 3 phase)
- FRN200G1E-4E (220kW 400V 3 phase)
- FRN220G1E-4E (250kW 400V 3 phase)
- FRN280G1E-4E (315kW 400V 3 phase)
- FRN315G1E-4E (355kW 400V 3 phase)
- FRN355G1E-4E (400kW 400V 3 phase)
- FRN400G1E-4E (450kW 400V 3 phase)
Fuji Electric Inverter Frenic Mega FRN30G1S-4A Series
Fuji Frenic Mega FRN***G1S-4A Series
- FRN0.4G1S-4A (0.4kW)
- FRN0.75G1S-4A (0.75kW)
- FRN1.5G1S-4A (1.5kW)
- FRN2.2G1S-4A (2.2kW)
- FRN3.7G1S-4A (3.7kW)
- FRN5.5G1S-4A (5.5kW)
- FRN7.5G1S-4A (7.5kW)
- FRN11G1S-4A (11kW)
- FRN15G1S-4A (15kW)
- FRN18.5G1S-4A (18.5kW)
- FRN22G1S-4A (22kW)
- FRN30G1S-4A (30kW)
- FRN37G1S-4A (37kW)
- FRN45G1S-4A (45kW)
- FRN55G1S-4A (55kW)
Fuji Electric Inverter Frenic Mega FRN7.5G1S-4A 7.5kW 400V 3-phase
Specifications
- Input Voltage : 3-phase 380 - 480V 50/60Hz
- Power Output : 7.5kW
- Analog Input : 4 - 20mA, 0 - 10V
- Output frequency : 0.1 - 500Hz
- Digital Input
- Overload tolerance level : 150% - 1m, 200% - 3s
- 16 level speed control
- Communications RS485
- Function : Run the larges load torque, PID, more energy efficient
- Protection : Current, Voltage, temperature, phase failure
Fuji Electric Inverter Frenic Mega series 3-phase 200V 0.4 – 90kW
FRN***G1S-2 type
- FRN0.4G1S-2A (3 phase 200V 0.4kW)
- FRN0.75G1S-2A (3 phase 200V 0.75kW)
- FRN1.5G1S-2A (3 phase 200V 1.5kW)
- FRN2.2G1S-2A (3 phase 200V 2.2kW)
- FRN3.7G1S-2A (3 phase 200V 3.7kW)
- FRN5.5G1S-2A (3 phase 200V 5.5kW)
- FRN7.5G1S-2A (3 phase 200V 7.5kW)
- FRN11G1S-2A (3 phase 200V 11kW)
- FRN15G1S-2A (3 phase 200V 15kW)
- FRN18.5G1S-2A (3 phase 200V 18.5kW)
- FRN22G1S-2A (3 phase 200V 22kW)
- FRN30G1S-2A (3 phase 200V 30kW)
- FRN37G1S-2A (3 phase 200V 37kW)
- FRN45G1S-2A (3 phase 200V 45kW)
- FRN55G1S-2A (3 phase 200V 55kW)
- FRN75G1S-2A (3 phase 200V 75kW)
- FRN90G1S-2A (3 phase 200V 90kW)
Fuji Electric Inverter Frenic Mega series 3-phase 400V 0.4 – 55kW
HD (High Duty) spec for heavy load type
- FRN0.4G1S-4A (3 phase 400V 0.4kW)
- FRN0.75G1S-4A (3 phase 400V 0.75kW)
- FRN1.5G1S-4A (3 phase 400V 1.5kW)
- FRN2.2G1S-4A (3 phase 400V 2.2kW)
- FRN3.7G1S-4A (3 phase 400V 3.7kW)
- FRN5.5G1S-4A (3 phase 400V 5.5kW)
- FRN7.5G1S-4A (3 phase 400V 7.5kW)
- FRN11G1S-4A (3 phase 400V 11kW)
- FRN15G1S-4A (3 phase 400V 15kW)
- FRN18.5G1S-4A (3 phase 400V 18.5kW)
- FRN22G1S-4A (3 phase 400V 22kW)
- FRN30G1S-4A (3 phase 400V 30kW)
- FRN37G1S-4A (3 phase 400V 37kW)
- FRN45G1S-4A (3 phase 400V 45kW)
- FRN55G1S-4A (3 phase 400V 55kW)
Fuji Electric Inverter Frenic Mini 0.1kW to 3.7kW 200V 3-phase
New Compact Inverter
- High performance and multipurpose
- Fully compatible with existing products
- Easy operation and maintenance
- Energy efficient
- Network capabilities standard
- Global compatibility
- FRN0.1C1S-2A : 0.1kW (1/8HP)
- FRN0.2C1S-2A : 0.2kW (1/4HP)
- FRN0.4C1S-2A : 0.4kW (1/2HP)
- FRN0.75C1S-2A : 0.75kW (1HP)
- FRN1.5C1S-2A : 1.5kW (2HP)
- FRN2.2C1S-2A : 2.2kW (3HP)
- FRN3.7C1S-2A : 3.7kW (5HP)
- FRN0.1C1E-2A : 0.1kW (1/8HP)
- FRN0.2C1E-2A : 0.2kW (1/4HP)
- FRN0.4C1E-2A : 0.4kW (1/2HP)
- FRN0.75C1E-2A : 0.75kW (1HP)
- FRN1.5C1E-2A : 1.5kW (2HP)
- FRN2.2C1E-2A : 2.2kW (3HP)
- FRN3.7C1E-2A : 3.7kW (5HP)
- FRN1.5C1S-2A21 : 1.5kW (2HP)
- FRN2.2C1S-2A21 : 2.2kW (3HP)
- FRN3.7C1S-2A21 : 3.7kW (5HP)
- FRN0.1C1J-2A : 0.1kW (1/8HP)
- FRN0.2C1J-2A : 0.2kW (1/4HP)
- FRN0.4C1J-2A : 0.4kW (1/2HP)
- FRN0.75C1J-2A : 0.75kW (1HP)
- FRN1.5C1J-2A : 1.5kW (2HP)
- FRN2.2C1J-2A : 2.2kW (3HP)
- FRN3.7C1J-2A : 3.7kW (5HP)
Fuji Electric Inverter Frenic Mini 0.4kW – 3.7kW 400V 3-phase
Frenic MIni 0.1kW to 3.7kW 200V 3-phase Variations
- FRN0002C2S-4A (0.4kW 400V 3-phase)
- FRN0004C2S-4A (0.75kW 400V 3-phase)
- FRN0005C2S-4A (1.5kW 400V 3-phase)
- FRN0007C2S-4A (2.2kW 400V 3-phase)
- FRN0011C2S-4A (3.7kW 400V 3-phase)
- High performance and multipurpose
- Fully compatible with existing products
- Easy operation and maintenance
- Energy efficient
- Network capabilities standard
- Global compatibility
Fuji Electric Inverter FRENIC-Eco 3-phase 400V Series
Variable Torque Load Inverters for Fans and Pumps
Inverter Fuji Electric FRENIC-Eco 3 phase 400V, 0.75kW - 560kW
Fuji Electric Inverter Frenic-HVAC Series
Low voltage AC drives for HVAC applications
- High performance enable by the comprehensive use of Fuji Technology
- Easy maintenance for the end-user
- Maintains safety and protects the environment
- Opens up possibilities for the new generation